KDC-DAB43U/ KDC-DAB4557U

10.3 Error messages

The messages shown below indicates your system condition.

ö "PLS EJECT"

Í The unit is malfunctioning for some reason.

ò Press and hold [G].

ò Press the reset button on the unit. If the "PLS EJECT" code does not disappear, consult your nearest service center.

ö "TOC ERROR"

Í The CD is quite dirty. The CD is upside-down. The CD is scratched a lot.

Í The disc is unreadable.

ö "PROTECT" (blink)

Í The speaker wire has short-circuited or touched the chassis of the vehicle, and then the protection function has been activated.

ò Lay or insulate the speaker cable properly and press the Reset button. If "PROTECT" does not disappear, consult your nearest service center.

ö "NA FILE"

Í An Audio file is played in a format that is not supported by this unit.

ö "COPY PRO"

Í A copy-protected file is played.

ö "READ ERROR"

Í The file system of the connected USB device is broken.

ò Copy the files and folders for the USB device again. If "Read Error" is still displayed, initialize the USB device or use another USB device.

ö "NO DEVICE"

Í A USB device is selected as a source although no USB device is connected.

ò Change the source to any source other than the USB device. Connect an USB device, and change the source to the USB device again.

ö "NA DEVICE"

Í An unsupported USB device is connected.

ò Check that the connected USB device is supported. See <About USB device>.

Í Connection to the iPod has failed.

ò Check that the connected iPod is supported. See <About compatible iPod/iPhone> for information on supported iPods.

ö "NO MUSIC"

Í The connected USB device contains no playable audio file.

Í A medium that does not have playable data has been played.

ö "USB ERROR"

Í Some trouble may have occurred to the connected USB device.

ò Remove the USB device, then cycle the power switch to ON. If the same display is repeated, use another USB device.

ö "iPod ERROR"

Í Connection to the iPod has failed.

ò Remove the iPod/ iPhone and then reconnect it.

ò Reset iPod/ iPhone.

ö "DAB ANT ERR"

Í The antenna has a short-circuit and the protective circuit has activated.

ò Check the DAB antenna. If a passive antenna without a booster is used, set DAB ANT PWR "OFF". See <DAB ANT PWR>.

Contents

• 1. SAFETY
  • 1.1 Safety precaution
  • 1.2 Important information
  • 1.3 Regulatory Compliance
• 2. GETTING STARTED
  • 2.1 Component names and functions
  • 2.2 Preparation
• 3. GENERAL
  • 3.1 Basic operations
  • 3.2 Adjusting the clock
  • 3.3 Changing the initial settings
  • 3.4 Setting the demonstration mode
  • 3.5 Muting upon the reception of a phone call
• 4. CD/ USB/ iPod
  • 4.1 Start playback
  • 4.2 Basic operations
  • 4.3 Music search
  • 4.4 Alphabet search
  • 4.5 Setting the skip search ratio
  • 4.6 More information
• 5. DIGITAL RADIO (DAB)
  • 5.1 Preparations
  • 5.2 Basic operations
  • 5.3 Selecting a service
  • 5.4 Alphabet Search for service
  • 5.5 PTY (Program Type)
  • 5.6 PTY Watch Select
  • 5.7 Announcement select
  • 5.8 Changing the digital radio settings
• 6. ANALOG RADIO
  • 6.1 Basic operations
  • 6.2 Auto memory
  • 6.3 PTY (Program Type)
  • 6.4 Changing the analog radio settings
• 7. AUX
  • 7.1 Start listening
  • 7.2 Set the AUX name
• 8. AUDIO SETTINGS
  • 8.1 Audio controls
• 9. DISPLAY SETTINGS
  • 9.1 Display & Illumination setting
  • 9.2 Adjusting the Illumination color
• 10. TROUBLESHOOTING
  • 10.1 Setting error
  • 10.2 Operation/ wiring error
  • 10.3 Error messages
• 11. SPECIFICATIONS
  • 11.1 Specifications of each section
  • 11.2 Trademarks