KDC-BT73DAB/KDC-BT53U/KDC-5057SD

17-3. Error messages

The messages shown below indicates your system condition.

ö "TOC Error"

Í The CD is quite dirty. The CD is upside-down. The CD is scratched a lot.

Í The disc is unreadable.

ö "IN" (blink)

Í The CD player section is not operating properly.

ò Reinsert the CD. If the CD cannot be ejected or the display continues to blink even when the CD has been properly reinserted, please switch off the power and consult your nearest service center.

ö "Protect" (blink)

Í The speaker wire has short-circuited or touched the chassis of the vehicle, and then the protection function has been activated.

ò Lay or insulate the speaker cable properly and press the Reset button. If "Protect" does not disappear, consult your nearest service center.

ö "NA File"

Í An Audio file is played in a format that is not supported by this unit.

ö "Copy PRO"

Í A copy-protected file is played.

ö "Read Error"

Í The file system of the connected USB device is broken.

ò Copy the files and folders for the USB device again. If "Read Error" is still displayed, initialize the USB device or use another USB device.

ö "No Device"

Í A USB device is selected as a source although no USB device is connected.

ò Change the source to any source other than the USB device. Connect a USB device, and change the source to the USB device again.

ö "N/A Device"

Í An unsupported USB device is connected.

Í Connection to the iPod has failed.

ò Check that the connected iPod is supported. See <8-6. About the Audio file> for information on supported iPods.

ö "No Music Data"

Í The connected USB device contains no playable audio file.

Í A medium that does not have playable data has been played.

ö "Please Eject"

Í The unit is malfunctioning for some reason.

ò Press and hold [G].

ò Press the reset button on the unit. If the "Please Eject" code does not disappear, consult your nearest service center.

ö "iPod Error"

Í Connection to the iPod has failed.

ò Remove the iPod and then reconnect it.

ò Reset iPod/ iPhone.

ö "No Number"

Í The calling party does not notify a caller ID.

Í There is no phone number data.

ö "No Data"

Í There is no outgoing call list.

Í There is no incoming call list.

Í There is no missed call list.

Í There is no phone book list.

ö "No Entry"

Í The cell phone has not been registered (pairing).

ö "HF Disconnect"

Í The unit cannot communicate with the cell phone.

ö "AUD Disconnect"

Í The unit cannot communicate with the Bluetooth audio player.

ö "HF Error 68"

Í The unit cannot communicate with the cell phone.

ò Cycle the power switch. If this message still appears, press the Reset button on the control unit.

ö "HF Error 89"

Í Update of the firmware has failed.

ò Retry update of the firmware.

ö "Device Full"

Í 5 Bluetooth device have already been registered. No more Bluetooth devices are registered.

ö "Pairing Failed"

Í Pairing error.

ö "N/A Voice Tag"

Í No voice tags are registered in your cell phone.

ö "No Phonebook"

Í Data is not contained in the phone book.

ö "No Support"

Í The connected Bluetooth device does not support a voice recognition function.

ö "No Active Device"

Í Any Bluetooth device supporting a voice recognition function is not connected.

ö "Antenna Error"

Í The antenna has a short-circuit and the protective circuit has activated.

ò Check the Digital Radio antenna. If a passive antenna without a booster is used, set "DAB Antenna Power" to "OFF". Refer to <10-10. Digital Radio initial settings>

aha Messages

ö "Disconnect"

Í Check the connection to the device.

ö "Check Device"

Í Set aha application active.

ö "Loading"

Í Log in to aha.

ö "Login Failed"

Í Logging in to aha has failed.

ö "Aha App Update Required"

Í Upgrade the aha application to the latest version.

ö "Aha Unavailable"

Í Maintenance of Aha Radio Server is in progress.

ö "Network Unavailable"

Í Connection to Aha Radio Server is impossible.

ö "Poor GPS"

Í GPS reception is impossible.

ö "Connect Phone"

Í Connect the cell phone.

ö "Action NA"

Í The pressed key is invalid.

ö "Select Station"

Í Select a station.

Contents

• 1. Before use
  • 1-1. Safety precaution
  • 1-2. Important information
  • 1-3. Regulatory Compliance
• 2. Appendix
  • 2-1. Specifications
  • 2-2. Trademarks
• 3. Basic operations
  • 3-1. Component names
  • 3-2. Preparations
  • 3-3. How to select the item
  • 3-4. General operations
• 4. Audio adjustments (KDC-5057SD)
  • 4-1. Audio control
  • 4-2. Audio preset
  • 4-3. Audio preset recall
• 5. DSP settings (KDC-BT73DAB, KDC-BT53U)
  • 5-1. Audio control
  • 5-2. Manual equalizer control
  • 5-3. Car type selection
  • 5-4. Speaker setting
  • 5-5. X’Over setting
  • 5-6. Listening position setting
  • 5-7. Delay time control
  • 5-8. Channel level fine adjustments
  • 5-9. Resetting of DTA Settings
  • 5-10. DSP preset
  • 5-11. DSP preset recall
• 6. Listen to the iPod
  • 6-1. Models of iPods/iPhones that can be connected to this unit
  • 6-2. Playing music
  • 6-3. Music search
  • 6-4. Alphabet search
  • 6-5. Direct search
  • 6-6. Skip search
  • 6-7. Skip search ratio setting
  • 6-8. Playback mode
  • 6-9. App & iPod mode setting
• 7. Aha Radio (KDC-BT73DAB, KDC-BT53U)
  • 7-1. Requirements Aha™
  • 7-2. Listening to the Aha Radio
  • 7-3. Basic operations
  • 7-4. Station search
  • 7-5. Calling a number in the content
  • 7-6. Aha source control
• 8. Listen to the CD/ Audio file
  • 8-1. Playing music
  • 8-2. Music search
  • 8-3. Skip search
  • 8-4. Skip search ratio setting
  • 8-5. Playback mode
  • 8-6. About the Audio file
  • 8-7. About the USB device
  • 8-8. About SD card
  • 8-9. About "KENWOOD Music Editor Light" and "KENWOOD Music Control"
  • 8-10. About the discs used with this unit
  • 8-11. Handling discs
• 9. Listen to the tuner
  • 9-1. Listening to the radio
  • 9-2. Station preset memory
  • 9-3. Auto memory
  • 9-4. Recall preset station
  • 9-5. Tuner setting
  • 9-6. PTY (Program Type)
• 10. Listen to the Digital Radio (KDC-BT73DAB)
  • 10-1. Listening to the Digital Radio
  • 10-2. Service preset memory
  • 10-3. Recall preset service
  • 10-4. Service list select
  • 10-5. Alphabet Search for service
  • 10-6. PTY (Program Type)
  • 10-7. Announcement setup
  • 10-8. Replay
  • 10-9. Digital Radio setting
  • 10-10. Digital Radio initial settings
• 11. Display settings
  • 11-1. Selecting a display type
  • 11-2. Information display setting
  • 11-3. Illumination color selection
  • 11-4. Adjusting the Illumination color
  • 11-5. Selecting a text display
  • 11-6. Display & Illumination setting
• 12. General settings
  • 12-1. Adjusting the clock
  • 12-2. Adjusting the date
  • 12-3. Clock & date display type setting
  • 12-4. Auxiliary input display setting
  • 12-5. Muting the audio upon reception of a phone call
  • 12-6. Demonstration mode setting
  • 12-7. Initial settings
• 13. Registering a Bluetooth (KDC-BT73DAB, KDC-BT53U)
  • 13-1. About the Bluetooth module
  • 13-2. Registering a Bluetooth device
  • 13-3. Selecting the Bluetooth device you wish to connect
  • 13-4. Deleting a registered Bluetooth device
  • 13-5. Bluetooth device registration test
• 14. Hands-free phoning (KDC-BT73DAB, KDC-BT53U)
  • 14-1. Receiving a call
  • 14-2. Calling a number in the phone book
  • 14-3. Dialing a number
  • 14-4. Calling a number in the call log
  • 14-5. Speed dialing (Preset dial)
  • 14-6. Registering in the preset dial number list
  • 14-7. During a call
  • 14-8. Clearing the disconnection message
  • 14-9. Voice Control
  • 14-10. Display of phone number types (categories)
• 15. Bluetooth audio (KDC-BT73DAB, KDC-BT53U )
  • 15-1. Before use
  • 15-2. Basic operations
  • 15-3. Playback mode
• 16. Bluetooth settings (KDC-BT73DAB, KDC-BT53U)
  • 16-1. Registering the PIN code
  • 16-2. Downloading the phone book
  • 16-3. Deleting the phone book
  • 16-4. Displaying the firmware version
  • 16-5. Switching between two connected cell-phones
  • 16-6. Bluetooth detail setting
• 17. Troubleshooting guide
  • 17-1. Setting error
  • 17-2. Operation/wiring error
  • 17-3. Error messages