KDC-U7056DAB/U7056BT/U7056BTL>4. DSP settings>4-5. X'Over setting

4-5. X'Over setting

Fine adjusting the following setting values corresponding to the X'Over values set in the section <4-4. Speaker setting>.

  1. Press [SRC] to select a source other than Standby ("STANDBY").

    Refer to <Source selection>.

  2. Press [Control] knob.

    Enters the Function setting mode.

  3. Select "Audio Control" > "Pro Setup" > "X'Over" using [Control] knob.

    For how to use [Control] knob, refer to <3-3. How to select the item>.

  4. Select a speaker type using [Control] knob.

    Speaker type

    Setting item

    Setting value

    "Front"

    "FC"

    Front high pass filter

    Through, 30, 40, 50, 60, 70, 80, 90, 100, 120, 150, 180, 220, 250 Hz

    "SLOPE"[1]

    Front high pass slope

    -6, -12, -18, -24 dB/Oct

    "GAIN"

    Front gain

    -8 ,-7, -6, -5, -4, -3, -2, -1, 0 dB

    "Rear"

    "FC"

    Rear high pass filter

    Through, 30, 40, 50, 60, 70, 80, 90, 100, 120, 150, 180, 220, 250 Hz

    "SLOPE"[1]

    Rear high pass slope

    -6, -12, -18, -24 dB/Oct

    "GAIN"

    Rear Gain

    -8, -7, -6, -5, -4, -3, -2, -1, 0 dB

    "SubWoofer"

    "FC"

    Subwoofer low pass filter

    30, 40, 50, 60, 70, 80, 90, 100, 120, 150, 180, 220, 250, Through Hz

    "SLOPE"[1]

    Subwoofer slope

    -6, -12, -18, -24 dB/Oct

    "GAIN"

    Subwoofer gain

    -8, -7, -6, -5, -4, -3, -2, -1, 0 dB

    "PHASE"

    Subwoofer phase

    "REV" (180°)/ "NML" (0°)

    "Tweeter"

    "FC"

    Shelving filter

    1, 1.6, 2.5, 4, 5, 6.3, 8, 10, 12.5 kHz

    "Volume"

    Tweete volume

    -8, -7, -6, -5, -4, -3, -2, -1, 0 dB

    (Colored text: Factory setting)

    [1] Displayed only when "FC" is set to "30" - "250".

    When Speaker network is set to 3 way

    Speaker type

    Setting item

    Setting value

    "Tweeter"

    "FC"

    Tweeter high pass filter

    1, 1.6, 2.5, 4, 5, 6.3, 8, 10, 12.5 kHz

    "SLOPE"

    Tweeter slope

    -6, -12 dB/Oct

    "GAIN"

    Tweeter gain

    -8 ,-7, -6, -5, -4, -3, -2, -1, 0 dB

    "PHASE"

    Tweeter phase

    "REV" (180°)/ "NML" (0°)

    "Mid LPF"

    "FC"

    Mid range low pass filter

    1, 1.6, 2.5, 4, 5, 6.3, 8, 10, 12.5, Through kHz

    "SLOPE"

    Mid range low pass slope

    -6, -12 dB/Oct

    "GAIN"

    Mid range gain

    -8, -7, -6, -5, -4, -3, -2, -1, 0 dB

    "PHASE"

    Mid range phase

    "REV" (180°)/ "NML" (0°)

    "Mid HPF"

    "FC"

    Mid range high pass filter

    Through, 30, 40, 50, 60, 70, 80, 90, 100, 120, 150, 180, 220, 250 Hz

    "SLOPE"

    Mid range high pass slope

    -6, -12 dB/Oct

    "GAIN"

    Mid range gain

    -8, -7, -6, -5, -4, -3, -2, -1, 0 dB

    "PHASE"

    Mid range phase

    "REV" (180°)/ "NML" (0°)

    "Woofer"

    "FC"

    Woofer low pass filter

    30, 40, 50, 60, 70, 80, 90, 100, 120, 150, 180, 220, 250, Through Hz

    "SLOPE"

    Woofer low pass slope

    -6, -12 dB/Oct

    "GAIN"

    Woofer gain

    -8, -7, -6, -5, -4, -3, -2, -1, 0 dB

    "PHASE"

    Woofer phase

    "REV" (180°)/ "NML" (0°)
  5. Select a setting item using [Control] knob.
  6. Select a setting value using [Control] knob.

Exiting from the Function setting mode

Press and hold [1/6].

Contents