KDC-U7056DAB/U7056BT/U7056BTL

4-7. Delay time control

Adjusting fine tuning of the speaker position compensation value specified at <4-3. Car type selection>.

Preparation for setting

• If you specify the distance from the center of the currently set listening position to every speaker, the delay time will be automatically computed and set.

  1. Determine the center of the currently set listening position as the reference point (• in the illustration shown below).

  2. Measure the distances from the reference point to the speakers.

  3. Calculate the differences between the distance of the furthest speaker and other speakers.

  4. Input the differences calculated in step 3 for individual speakers.

  5. Adjust gain for individual speakers. A sound image will be shifted to the speaker with increased gain.

  Example: When "Front" is selected as the listening position (<4-6. Listening position setting>).

  

  When Speaker network is set to 3 way

  

1. Press [SRC] to select a source other than Standby ("STANDBY").

   Refer to <Source selection>.

2. Press [Control] knob.

   Enters the Function setting mode.

3. Select "Audio Control" > "Pro Setup" > "DTA Settings" > "DTA" using [Control] knob.

   For how to use [Control] knob, refer to <3-3. How to select the item>.

4. Select a speaker using [Control] knob.

   Speaker	Display	Range
   Front Left speaker	"FrontL"	0 – 610 cm
   Front Right speaker	"FrontR"	0 – 610 cm
   Rear Left speaker	"RearL"	0 – 610 cm
   Rear Right speaker	"RearR"	0 – 610 cm
   Subwoofer Left	"SW L"	0 – 610 cm
   Subwoofer Right	"SW R"	0 – 610 cm

   (Colored text: Factory setting)

   When Speaker network is set to 3 way

   Speaker	Display	Range
   Tweeter Left	"TWL"	0 – 610 cm
   Tweeter Right	"TWR"	0 – 610 cm
   Mid Range Left	"MIDL"	0 – 610 cm
   Mid Range Right	"MIDR"	0 – 610 cm
   Woofer Left	"WFL"	0 – 610 cm
   Woofer Right	"WFR"	0 – 610 cm

   (Colored text: Factory setting)

5. Select a value using [Control] knob.

Exiting from the Function setting mode

Press and hold [1/6].

Contents

• 1. Before use
  • 1-1. Safety precaution
  • 1-2. Important information
  • 1-3. Regulatory Compliance
• 2. Appendix
  • 2-1. Trademarks
• 3. Basic operations
  • 3-1. Component names
  • 3-2. Preparations
  • 3-3. How to select the item
  • 3-4. Adjusting the clock
  • 3-5. General operations
• 4. DSP settings
  • 4-1. Audio control
  • 4-2. Manual equalizer control
  • 4-3. Car type selection
  • 4-4. Speaker setting
  • 4-5. X'Over setting
  • 4-6. Listening position setting
  • 4-7. Delay time control
  • 4-8. Channel level fine adjustments
  • 4-9. Resetting of DTA Settings
  • 4-10. DSP preset
  • 4-11. DSP preset recall
• 5. Listen to the iPod
  • 5-1. Models of iPods/iPhones that can be connected to this unit
  • 5-2. Playing music
  • 5-3. Music search
  • 5-4. Alphabet search
  • 5-5. Direct search
  • 5-6. Skip search
  • 5-7. Skip search ratio setting
  • 5-8. Playback mode
  • 5-9. App & iPod mode setting
• 6. Pandora® (KDC-U7056DAB/ KDC-U7056BT)
  • 6-1. Requirements Pandora®
  • 6-2. Listening to the Pandora®
  • 6-3. Basic operation
  • 6-4. Station search
  • 6-5. Bookmark registration
  • 6-6. New Station Creation
  • 6-7. Deletion of station
  • 6-8. Pandora source control
• 7. Aha Radio
  • 7-1. Requirements Aha™
  • 7-2. Listening to the Aha Radio
  • 7-3. Basic operations
  • 7-4. Station search
  • 7-5. Calling a number in the content
  • 7-6. Aha source control
• 8. Listen to the CD/ Audio file
  • 8-1. Playing music
  • 8-2. Music search
  • 8-3. Skip search
  • 8-4. Skip search ratio setting
  • 8-5. Playback mode
  • 8-6. Direct music search
  • 8-7. About the Audio file
  • 8-8. About the USB device
  • 8-9. About "KENWOOD Music Editor Light" and "KENWOOD Music Control"
  • 8-10. About the discs used with this unit
  • 8-11. Handling discs
• 9. Listen to the tuner
  • 9-1. Listening to the radio
  • 9-2. Station preset memory
  • 9-3. Auto memory
  • 9-4. Recall preset station
  • 9-5. Tuner setting
  • 9-6. Direct access tuning
  • 9-7. PTY (Program Type)
  • 9-8. Frequency step setting
• 10. Listen to the Digital Radio (KDC-U7056DAB)
  • 10-1. Listening to the Digital Radio
  • 10-2. Service preset memory
  • 10-3. Recall preset service
  • 10-4. Service list select
  • 10-5. Alphabet Search for service
  • 10-6. PTY (Program Type)
  • 10-7. Announcement setup
  • 10-8. Replay
  • 10-9. Digital Radio setting
  • 10-10. Digital Radio initial settings
• 11. Display settings
  • 11-1. Selecting a display type
  • 11-2. Information display setting
  • 11-3. Illumination color selection
  • 11-4. Adjusting the Illumination color
  • 11-5. Selecting a text display
  • 11-6. Display & Illumination setting
• 12. General settings
  • 12-1. Adjusting the date
  • 12-2. Clock & date display type setting
  • 12-3. Auxiliary input display setting
  • 12-4. Demonstration mode setting
  • 12-5. Initial settings
• 13. Registering a Bluetooth
  • 13-1. About the Bluetooth module
  • 13-2. Registering a Bluetooth device
  • 13-3. Selecting the Bluetooth device you wish to connect
  • 13-4. Deleting a registered Bluetooth device
  • 13-5. Bluetooth device registration test
• 14. Hands-free phoning
  • 14-1. Receiving a call
  • 14-2. Calling a number in the phone book
  • 14-3. Dialing a number
  • 14-4. Calling a number in the call log
  • 14-5. Speed dialing (Preset dial)
  • 14-6. Registering in the preset dial number list
  • 14-7. During a call
  • 14-8. Clearing the disconnection message
  • 14-9. Voice Control
  • 14-10. Display of phone number types (categories)
• 15. Bluetooth audio
  • 15-1. Before use
  • 15-2. Basic operations
  • 15-3. Playback mode
• 16. Bluetooth settings
  • 16-1. Registering the PIN code
  • 16-2. Downloading the phone book
  • 16-3. Deleting the phone book
  • 16-4. Displaying the firmware version
  • 16-5. Switching between two connected cell-phones
  • 16-6. Bluetooth detail setting
• 17. Basic operation of remote control
  • 17-1. Before using remote control
  • 17-2. Basic opreation
• 18. Troubleshooting guide
  • 18-1. Setting error
  • 18-2. Operation/wiring error
  • 18-3. Error messages